|
Namazu for hns による簡易全文検索 詳しくは 詳細指定/ヘルプを参照して下さい |
||||||||||||||||||||||||||||||||||||||||||||||||||
2016年01月25日(月) 旧暦 [n年日記] [更新:"2016/01/25 10:01:12"]#1 [NetBSD] bge0 gets no carrier with NetBSD/i386 5.2
With the box DELL T105, netbooting goes fine while the sysinst after that
gets no carrier on bge0 interface, strange.
(netbooting NetBSD/i386 5.2.2)
bge0 at pci2 dev 0 function 0: Broadcom BCM5722 Gigabit Ethernet bge0: interrupting at ioapic0 pin 1 adjust device control 0x102000 -> 0x105000 bge0: ASIC BCM5755 C0 (0xa200), Ethernet address 00:1e:c9:56:98:56 bge0: setting short Tx thresholds brgphy0 at bge0 phy 1: BCM5722 1000BASE-T media interface, rev. 0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto # ifconfig -a bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx, TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx> enabled=0 address: 00:1e:c9:56:98:56 media: Ethernet autoselect (100baseTX full-duplex) status: active # ifconfig -a bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx> enabled=0 address: 00:1e:c9:56:98:56 media: Ethernet 100baseTX full-duplex status: active inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255 inet6 fe80::21e:c9ff:fe56:9856%bge0 prefixlen 64 scopeid 0x1 lo0: flags=8048<LOOPBACK,RUNNING,MULTICAST> mtu 33192 # ifconfig bge0 192.168.60.29 # ifconfig -a bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx> enabled=0 address: 00:1e:c9:56:98:56 media: Ethernet 100baseTX full-duplex status: active inet 192.168.60.29 netmask 0xffffff00 broadcast 192.168.60.255 inet6 fe80::21e:c9ff:fe56:9856%bge0 prefixlen 64 scopeid 0x1 lo0: flags=8048<LOOPBACK,RUNNING,MULTICAST> mtu 33192 # ( つっこみ )
|
最近の日記 2024年05月08日 ・comparison on ./buildsh tools 2024年05月06日 ・py-setuptools (python 3.11.9) ・make release took 1 hours and 10 min ・qemu invocation for 10.99.10 2024年05月05日 ・Windows 10 version ・serial connection ・bc bench 2024年05月04日 ・Trial on 10.99.10 ・another version (later trial) to succeed 2024年04月29日 ・dkim | ||