hns - 日記自動生成システム - Version 2.19.9

先月 2014年12月 来月
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30 31
Namazu for hns による簡易全文検索
詳しくは 詳細指定/ヘルプを参照して下さい
検索式:

2014年12月27日() 旧暦 [n年日記] [更新:"2004/08/09 23:43:33"]

#1 [ML115] SM-CLP on console

ML115 (G5) を Wake up on Lan にするには (bios の設定画面がないので) ethtool を使うという話がある。しかし BSD では wip/ethtool はあるものの、これは Linux only ということらしい。ただ BIOS に IPMI という選択肢があるので、これを試す。 Bios の入口から Advanced Settings TAB を選ぶ。
Advanced Settings
  - CPU
  - HDD
  - IO
  - ACPI
  - APM
  - Event Log
  - IPMI Configuration
  - Console Redirection
  - USB Configuration
 Video Card Support	  [Enabled]
この中の IPMI と Console redirection が関係がある。
 IPMI - SEL Configuration     ( System Event Log)
      - Serial Port Configuration
      - Watchdog Configuration
      - Hardware health information

 Console  Enable/Disable
          BMC SPCR
          Serial
その中の Serial を選ぶと
Serial Port Assignment        BMC or System
Serial Port Switching         Enable/Disable
Serial Port Connection Mode   direct
のような画面になる。この二つ目を選ぶと、右に、次の切換鍵 (hot key) の説明がある
ESC (  BMC
ESC Q  System
Configure Console Redirection
Console Redirection         [ Enabled/Disabled ]
EMS support (SPCR)          [ Enabled/Disabled ]

Serial Port Mode            [ 115200 8,n,1 ]
Redirection After BIOS POST [Disabled/Boot Loader/Always]
Terminal Mode		    [ANSI]

IPMI:

Login: xxxx
Password: *****

CLP Session Initiated
/./-> 
Command Line Interface (CLI)
Copyright 2004-2006 Server Engines LLC
All rights reserved.
Login: 
何もしないで放っておくと、上のように Login: が出る。
Login と password は容易に想像出来る文字列を二回使う。
CLP Session Initiated
/./-> cd system1
/./system1/-> help
Host System Directory
/./system1/-> show
    /./system1
    Targets
        oemhp_sensors
        oemhp_frus
        led1
        
    Properties
        name=Hewlett-Packard
        enabledstate=enabled
        
    Verbs
        cd
        version
        exit
        show
        reset
        start
        stop
        help
        
/./system1/-> 
ここで
start .. Power On
reset .. reset or Power ON
stop  .. Power Off
ただし、本当にいきなり切る

実は以前にも試した記憶があるが、その時には、何か、「これはだめだ」 と思ったような気がするが、それが何だったかは覚えていない。今回はうまく行っている。

cd show and cd ..:

ちなみに CLP で何と入力するか、の話だけれど、 ls の代りに show と入力する(ような感じ)。
Targets で表示された中に cd するか show で調べる。



最近の日記
2024年05月08日
comparison on ./buildsh tools
2024年05月06日
py-setuptools (python 3.11.9)
make release took 1 hours and 10 min
qemu invocation for 10.99.10
2024年05月05日
Windows 10 version
serial connection
bc bench
2024年05月04日
Trial on 10.99.10
another version (later trial) to succeed
2024年04月29日
dkim
以上、1 日分です。
タイトル一覧
カテゴリ分類
Powered by hns-2.19.9, HyperNikkiSystem Project

Count.cgi (since 2000/02/05)