I've got junk CF-SX2, intending to take LCD to replace broken LCD for the another SX2.
The photo on Auction site seemed a little bit different, the frame size
was a little bit wide. And another intention is to take power related parts
to replace another SX2 which the power line is broken.
All the work went fine, except the I broke frame (Junk side) which I did
not notice the way to un assemble. I should have LCD and body get flat, and just
should have move the body to upper. I did not loose anything by this, because
I do not need this parts.
- Old one: junk, BIOS password is set and unknown. LCD looks OK
- Newer one: Working but LCD was broken
- The LCD panel is really a little bit small. It is OK, a kind of expected,
- The connector location is different on LCD side, the newer one cable was too short to reach
- I've picked the LCD cable from the old one and use it
- I took hard time to connect the LCD cable to LCD, right/left or flipped or not,
but finally resovled by
referencing the another set of LCD/cable combination of which LCD is broken.
- Then .. the RAM mapping is different.
four console windows appear
- And worse, X11 won't work (won't show meaningfull screen)
- On the way to this swap work, I've replaced the internal RAM from 4GB to 8GB, so now total get 16GB, see below
LCD のこわれた Let's Note CF-SX2 が二台ある。以前に新品の液晶だけ買ったことがあるが、
何とはなく良い思い出がなくて、避けていた。それで NX2 の パスワード付のジャンクがあって、
写真で、枠が少し広いかな、と思ったのだけれど、まあ、何とかなるかなと思って落札した
(Let's Note CF-NX2 RWJCS、 2,700 円 + 1,400円 送料)
確かに LCD が少し小さかったが、まあ、許容範囲かなと。ところが、
- まず、線が短かかった。LCD 側のコネクタの位置が違う。これは万事休す、かなと 思ったが、LCD への線までも交換することで何とかなった
- 線と LCD の接続は、どちら向きかなかなか理解出来なかったが、以前の割れた LCD があって、それの接続を見て、何とか理解し、うまく差せた
- それで動作確認をしたが、何と、RAM の mapping が違う
console の時は、それでも読めるので、LCD 無よりはよっぽど良いが、実は X Windows 11
は全然絵にならない。いづれ、取替えることとしよう。
＠
RAM 16GB:
ただし、ついでに内蔵の RAM を 8GB に交換したので、全部で 16GB になった
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 9.99.48 (GENERIC-no-SYNAPTICS) #4: Sat Feb 29 11:00:49 JST 2020
root@CF-SX2:/tmp/O/sys/arch/amd64/compile/GENERIC-no-SYNAPTICS
total memory = 16246 MB
avail memory = 15747 MB
sysctl_createv: sysctl_locate(maxtypenum) returned 2
pool redzone disabled for 'buf4k'
pool redzone disabled for 'buf64k'
cpu_rng: RDRAND
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Panasonic Corporation CF-SX2LDHCS (002)
Clean up all keytop. Today, it was fine day and sun light shed the
keyboard and told me it was too dirty. So cleaned up.
Have cvs update with tag netbsd-6, and patch with Kawauchi version,
cvs update -r netbsd-6 -dPA
zcat testing/evbppc/patch-current/.tmp/20120227.evbppc-current.diff.bz2 \
patch -s -p0
(I had removed some directories and files which were generated by previous
patch operation.)
time sudo ./build.sh -j 8 -m evbppc release |& tee ../log/20120227-kurobox-2
===> Successful make release
===> build.sh ended: Wed Feb 29 00:07:30 JST 2012
===> Summary of results:
build.sh command: ./build.sh -j 8 -m evbppc release
build.sh started: Tue Feb 28 22:37:41 JST 2012
NetBSD version: 6.0_BETA
MACHINE: evbppc
MACHINE_ARCH: powerpc
Build platform: NetBSD 5.1 amd64
HOST_SH: /bin/sh
TOOLDIR path: /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64
DESTDIR path: /export/src-netbsd-6-patched/obj/destdir.evbppc
RELEASEDIR path: /export/src-netbsd-6-patched/obj/releasedir
Updated makewrapper:
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/nbmake-evbppc
Successful make release
build.sh ended: Wed Feb 29 00:07:30 JST 2012
===> .
12272.08s 2245.95s 1:29:50.01 269% 0+0k 27220+41732io 143559pf+0w
0.55s 12.15s 1:29:50.02 0% 0+0k 0+1129io 12pf+0w
Following patch was NOT include in above
diff -u etc/etc.evbppc/Makefile.inc etc/etc.evbppc/.*Make*
--- etc/etc.evbppc/Makefile.inc 2012-02-27 22:58:45.000000000 +0900
+++ etc/etc.evbppc/.#Makefile.inc.1.8 2012-01-18 21:56:26.000000000 +0900
....
-KERNEL_SETS+= MPC8536DS MPC8548CDS P2020DS P2020RDB RB800
+KERNEL_SETS+= MPC8536DS MPC8548CDS P2020DS P2020RDB RB800 KUROBOX
So, I did following to get kernel
sudo rm -rf /export/src-netbsd-6-patched/sys/arch/evbppc/compile/obj
time sudo ./build.sh -m evbppc -j 8
-T /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64 kernel=KUROBOX
and got fine results
# link KUROBOX/netbsd
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-ld \
-Map netbsd.map --cref -N
-T /export/src-netbsd-6-patched/sys/arch/powerpc/conf/kern.ldscript \
-Ttext 0x90000 -e __start -S -o netbsd ${SYSTEM_OBJ} ${EXTRA_OBJ} vers.o
NetBSD 6.0_BETA (KUROBOX) #0: Wed Feb 29 08:48:42 JST 2012
text data bss dec hex filename
3543368 485276 161816 4190460 3ff0fc netbsd
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-dbsym netbsd
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-objcopy
-O binary netbsd netbsd.bin
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-objcopy
-S -O binary netbsd netbsd.bin
===> Kernels built from KUROBOX:
/export/src-netbsd-6-patched/sys/arch/evbppc/compile/obj/KUROBOX/netbsd
===> build.sh ended: Wed Feb 29 08:48:44 JST 2012
===> Summary of results:
build.sh command:
./build.sh -m evbppc -j 8 \
-T /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64 kernel=KUROBOX
build.sh started: Wed Feb 29 08:47:26 JST 2012
NetBSD version: 6.0_BETA
MACHINE: evbppc
MACHINE_ARCH: powerpc
Build platform: NetBSD 5.1 amd64
HOST_SH: /bin/sh
TOOLDIR path: /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64
DESTDIR path: /export/src-netbsd-6-patched/obj/destdir.evbppc
RELEASEDIR path: /export/src-netbsd-6-patched/obj/releasedir
Updated makewrapper:
/export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/nbmake-evbppc
Building kernel without building new tools
Building kernel: KUROBOX
Build directory:
/export/src-netbsd-6-patched/sys/arch/evbppc/compile/obj/KUROBOX
Kernels built from KUROBOX:
/export/src-netbsd-6-patched/sys/arch/evbppc/compile/obj/KUROBOX/netbsd
build.sh ended: Wed Feb 29 08:48:44 JST 2012
===> .
169.33s 37.62s 1:18.14 264% 0+0k 56+160io 3531pf+0w
sys/arch/evbppc/conf/INSTALL_KUROBOX
include "arch/evbppc/conf/KUROBOX"
#ident "INSTALL_KUROBOX-$Revision$"
include "arch/evbppc/conf/INSTALL.inc"
% cvs diff etc/etc.evbppc/Makefile.inc
Index: etc/etc.evbppc/Makefile.inc
===================================================================
RCS file: /cvs/cvsroot/src/etc/etc.evbppc/Makefile.inc,v
retrieving revision 1.10
diff -u -r1.10 Makefile.inc
--- etc/etc.evbppc/Makefile.inc 4 Feb 2012 10:32:11 -0000 1.10
+++ etc/etc.evbppc/Makefile.inc 29 Feb 2012 00:36:10 -0000
@@ -7,9 +7,11 @@
# to update the release documentation in distrib/notes/common/contents
KERNEL_SETS= WALNUT EXPLORA451 OPENBLOCKS200 OPENBLOCKS266
+KERNEL_SETS+= KUROBOX
KERNEL_SETS+= EV64260 PMPPC
KERNEL_SETS+= MPC8536DS MPC8548CDS P2020DS P2020RDB RB800
KERNEL_SUFFIXES= img
BUILD_KERNELS= INSTALL_WALNUT INSTALL_OPENBLOCKS266 INSTALL_PMPPC
+BUILD_KERNELS+= INSTALL_KUROBOX
BUILD_KERNELS+= INSTALL_P2020DS INSTALL_P2020RDB
To get INSTALL MD kernel,
- Have INSTALL_KUROBOX kernel built, by
sudo ./build.sh -j 8 -m evbppc \
-T /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64 \
kernel=INSTALL_KUROBOX
- cd distrib/evbppc/md-kernel
- Have Makefile modified
Index: Makefile
===================================================================
RCS file: /cvs/cvsroot/src/distrib/evbppc/md-kernel/Makefile,v
retrieving revision 1.3
diff -u -r1.3 Makefile
--- Makefile 3 Aug 2005 14:55:37 -0000 1.3
+++ Makefile 1 Mar 2012 02:28:31 -0000
@@ -8,8 +8,7 @@
RAMDISKDIR!= cd ${.CURDIR}/../ramdisk && ${PRINTOBJDIR}
RAMDISK= ${RAMDISKDIR}/ramdisk.fs
-MDSETTARGETS= INSTALL_WALNUT ${RAMDISK} - \
- INSTALL_OPENBLOCKS266 ${RAMDISK} -
+MDSETTARGETS= INSTALL_KUROBOX ${RAMDISK} -
MDSET_RELEASEDIR= binary/kernel
MDSET_SUFFIXES.-= img create-img
- did make by
sudo /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/nbmake-evbppc
- objcopy by
sudo /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-objcopy \
-O binary \
./obj/netbsd-INSTALL_KUROBOX ./obj/netbsd-INSTALL_KUROBOX.bin
(objcopy has been done already..)
t-105@makoto 11:59:49/120301(/export/src-netbsd-6-patched)% \
(cd sys/arch/evbppc/compile/obj/KUROBOX/; ls -l netbsd*)
-rwxr-xr-x 1 root wheel 4556759 Feb 29 08:49 netbsd
-rwxr-xr-x 1 root wheel 4028732 Feb 29 08:48 netbsd.bin
-rw-r--r-- 1 root wheel 4302036 Feb 29 08:48 netbsd.map
t-105@makoto 11:59:55/120301(/export/src-netbsd-6-patched)% \
(cd sys/arch/evbppc/compile/obj/INSTALL_KUROBOX/; ls -l netbsd*)
-rwxr-xr-x 1 root wheel 7697406 Feb 29 08:55 netbsd
-rwxr-xr-x 1 root wheel 7169596 Feb 29 08:54 netbsd.bin
-rw-r--r-- 1 root wheel 4327152 Feb 29 08:54 netbsd.map
This kernel boots fine on TeraStation.
The
dmesg is here.
＠
raidctl was not included in INSTALL_KUROBOX kernel,:
cd distrib/evbppc/ramdisk/
vi distrib/evbppc/ramdisk/list
Index: evbppc/ramdisk/list
===================================================================
RCS file: /cvs/cvsroot/src/distrib/evbppc/ramdisk/list,v
retrieving revision 1.18
diff -u -r1.18 list
--- evbppc/ramdisk/list 1 Feb 2012 22:25:46 -0000 1.18
+++ evbppc/ramdisk/list 1 Mar 2012 07:11:38 -0000
@@ -17,6 +17,7 @@
PROG bin/pax usr/bin/tar
PROG bin/pwd
PROG bin/ps
+PROG bin/raidctl
PROG bin/rcmd
PROG bin/rcp
PROG bin/rm
cd distrib/evbppc/ramdisk/
sudo /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/nbmake-evbppc
ls obj/
cd ../md-kernel/
sudo /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/nbmake-evbppc
sudo /export/src-netbsd-6-patched/obj/tooldir.NetBSD-5.1-amd64/bin/powerpc--netbsd-objcopy
-O binary ./obj/netbsd-INSTALL_KUROBOX ./obj/netbsd-INSTALL_KUROBOX.bin
Strange, rebooting this kernel still not having raidctl. why ?
It is not under /bin,
instead, should be under /sbin. Correct patch should look like this.
Index: evbppc/ramdisk/list
===================================================================
RCS file: /cvs/cvsroot/src/distrib/evbppc/ramdisk/list,v
retrieving revision 1.18
diff -u -r1.18 list
--- evbppc/ramdisk/list 1 Feb 2012 22:25:46 -0000 1.18
+++ evbppc/ramdisk/list 1 Mar 2012 07:29:30 -0000
@@ -47,6 +47,7 @@
PROG sbin/newfs_ext2fs
PROG sbin/newfs_msdos
PROG sbin/ping
+PROG sbin/raidctl
PROG sbin/reboot sbin/halt
PROG sbin/restore sbin/rrestore
PROG sbin/route
No, not yet, shall I need make clean ? Even after make clean at ramdisk,
I did not get raidctl yet. Shall I make clean under sysinst ?
I was copying from wrong obj directory. Now I got it.
And then, next problem is missing device file.
Index: ./evbppc/ramdisk/Makefile
===================================================================
RCS file: /cvs/cvsroot/src/distrib/evbppc/ramdisk/Makefile,v
retrieving revision 1.11
diff -u -r1.11 Makefile
--- ./evbppc/ramdisk/Makefile 1 Feb 2012 21:57:13 -0000 1.11
+++ ./evbppc/ramdisk/Makefile 1 Mar 2012 08:37:56 -0000
@@ -21,6 +21,7 @@
${NETBSDSRCDIR}/etc/netconfig ${DISTRIBDIR}/common/protocols \
${DISTRIBDIR}/common/services
MAKEDEVTARGETS= std md0 wd0 wd1 wd2 wd3 cd0 cd1 sd0 sd1 sd2 sd3 st0 pty0 ttyv0
+MAKEDEVTARGETS+= raid0 raid1 raid2
MAKEDEVTARGETS+= ld0 ld1
# Use stubs to eliminate some large stuff from libc
(We need make clean at ramdisk to have above patch effective. It is Makefile and
it is mostly natural. Who includes Makefile for the dependency :-)
ugen0 at uhub1 port 1
ugen0: Silicon Labs LOGJ200, rev 1.10/1.00, addr 2
都内某所で入手して来た USB one segment tuner。
(PCTV-hiwasa mini)
ここは電波が弱いはずなので、まず窓機でそちらを確認。
初めのうちは、「電波状態が不安定」という表示だったが、
しばらく放っておいたら TBS だけは入感している。
実は、東京タワーの方向に高い建物があって、この辺は
空中にアンテナを立てている人はいなくて、全て有線テレビ
(cable TV) が無料で利用出来ている。
しかし、その建物が取壊しになって、今は別の建物を建築中。
多分そのせいで、電波が少しとどいているらしい。
実は偏波を合せたら、更にもう少し入るようになった。
要するに外部空中線を縦にしたということ。
21 22 24 25 27 が見える。
次の日になって、地域の設定を千葉にしたのも一つの理由か
21 22 24 26 27 30 が見えている。
