Bootcode Ver.1.11 for [HGLAN]
Build:May 17 2005 [14:11:09]
isUseRevClock=0

******* Product Information *******
----------------------------------
Product Name: HD-HGLAN(IEMITSU)
          VER: 2.08
         Date: 2006/2/9 12:0:6
----------------------------------
Firmware check:done.

>>root=/dev/hda1
hit any key to boot EM mode.
    cmd_buf=root=/dev/ram0
Now Loading...done.
Now Booting
KERNELBASE=c0000000 r6=900030 r7=90003e
cmd_line=root=/dev/ram0
--- force EM mode
Memory BAT mapping: BAT2=128Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.20_mvl31-ppc_linkstation (root@sugai-linux) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Thu, 09 Feb 2006 11:56:26 +0900
BUFFALO Network Attached Storage Series
(C) 2002-2005 BUFFALO INC.
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram0
OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at 80040000
decrementer frequency = 32.768000 MHz 
Calibrating delay loop... 174.48 BogoMIPS
Memory: 125436k available (1448k kernel code, 568k data, 76k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
BUFFALO INC. RTC driver ver 1.00
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x80004600 (irq = 25) is a ST16650
ttyS01 at 0x80004500 (irq = 24) is a ST16650
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
IT8212: IDE controller on PCI bus 00 dev 60
IT8212: chipset revision 19
IT8212: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xbffed0-0xbffed7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xbffed8-0xbffedf, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC23200L, ATA DISK drive
ide0 at 0xbffef8-0xbffeff,0xbffef6 on irq 17
blk: queue c0206038, I/O limit 4095Mb (mask 0xffffffff)
hda: 6346368 sectors (3249 MB) w/256KiB Cache, CHS=6296/16/63, UDMA(33)
Partition check:
 hda:hda: dma_timer_expiry: dma status == 0x61
hda: dma_timer_expiry: dma status == 0x61
-- BREAK DMA (hda) --
   0x60
hda: dma_timer_expiry: status=0x58 { DriveReady SeekComplete DataRequest }
hda: irq timeout: status=0xd0 { Busy }
hda: DMA disabled
ide0: reset: success
 hda1 hda2 hda3
RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
eth0: RTL8169s/8110s Gigabit Ethernet driver 2.2+1 at 0xc9000f00, 00:0d:0b:69:7c:e5, IRQ 16
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
physmap flash device: 400000 at ffc00000
Search for id:(20 20) interleave(1) type(1)
Search for id:(20 20) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(20 5d) interleave(1) type(2)
Found: ST M29W324DB
linkstation_flash: Found 1 x16 devices at 0x0 in 8-bit mode
number of JEDEC chips: 1
Using physmap partition definition
Creating 5 MTD partitions on "linkstation_flash":
0x00000000-0x00300000 : "mtd0"
0x00300000-0x00370000 : "mtd1"
0x00370000-0x00380000 : "mtd2"
0x00380000-0x00400000 : "mtd3"
0x00000000-0x00400000 : "mtd4"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:0e.2: PCI device 1033:00e0
ehci_hcd 00:0e.2: irq 19, pci mem c9002f00
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0e.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, BUFFALO:it must be zero for PPC8241/8245
ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 5 ports detected
usb-ohci.c: USB OHCI at membase 0xc9004000, IRQ 19
usb-ohci.c: usb-00:0e.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xc9006000, IRQ 19
usb-ohci.c: usb-00:0e.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: AppleTalk 0.18a for Linux NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1996k freed
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 76k init
kmod: failed to exec /sbin/modprobe -s -k char-major-4, errno = 2
INIT: version 2.78 booting
EXT2-fs warning: checktime reached, running e2fsck is recommended
[: 0: unexpected operator
Mounting local filesystems...
none on /dev/pts type devpts (rw,gid=5,mode=20)
Cleaning: /tmp .
Configuration network interface: lo eth0
Starting system log daemon: syslogd klogd.
INIT: Entering runlevel: 2
Starting AP serv daemon:AP serv starting on eth0
Starting internet superserver: inetd.
Start services: ppc_uartd


BUFFALO INC. Link Station series HD-HGLAN (IEMITSU)

HD-HGLAN-EM login: